polarisjay.blogg.se - Mac os x install disc for pwerbook g4

#MAC OS X INSTALL DISC FOR PWERBOOK G4 HOW TO#
#MAC OS X INSTALL DISC FOR PWERBOOK G4 MAC OS X#
#MAC OS X INSTALL DISC FOR PWERBOOK G4 NO CD#
#MAC OS X INSTALL DISC FOR PWERBOOK G4 DRIVERS#
#MAC OS X INSTALL DISC FOR PWERBOOK G4 DRIVER#

t - Put FireWire machine into FireWire Target Disk mode.

r - Force PowerBooks to reset the screen.

n - Hold down until Mac logo, will attempt to boot from network server (using BOOTP or TFTP).

d - Force the internal hard disk to be the startup device.

#MAC OS X INSTALL DISC FOR PWERBOOK G4 NO CD#

If set to boot to X and no CD is present, may boot to 9.

cmd-opt-a-v - Force an AV monitor to be recognized as one.

cmd-opt-x-o - Boot from ROM (Mac Classic only).

cmd-opt-t-v - Force Quadra AV machines to use TV as a monitor.

cmd-opt-shift-delete-# - Boot from a specific SCSI ID # (# = SCSI ID number).

For SCSI devices it searches from highest ID to lowest for a partition with a bootable system.

#MAC OS X INSTALL DISC FOR PWERBOOK G4 DRIVER#

This actually forces the system to NOT load the driver for the default volume, which has the side effect mentioned above.

cmd-opt-shift-delete - Bypass startup drive and boot from external (or CD).

#MAC OS X INSTALL DISC FOR PWERBOOK G4 MAC OS X#

cmd-x (or just x?) - Will boot into Mac OS X if 9 and X are on the same partition and that's the partition you're booting from.cmd-opt - Hold down until 2nd chime, will boot into Mac OS 9 ?.opt - Bring up OF system picker on New World machines.mouse down - Eject removable media ( I think Boot ROMs prior to 2.4f1 excluded the CD drive ).I have the next list of magical boot key sequences: I figured my trick was shot as soon as the Duo Core machines came out, but I now realize there are quite a few people with PPC Macs that might be able to use this hint.

#MAC OS X INSTALL DISC FOR PWERBOOK G4 HOW TO#

So the two ways that I know how to enable it are through terminal by using the nvram command, and directly in Open Firmware. In the optional boot menu (reached by holding down the Option key during boot), it also will not show.

So in System Preferences, the USB disk will not be shown as a bootable drive. If the firmware cannot list the contents of the drive, it seems it cannot boot off of it.Īs you should know (thanks to the owner of the iMac G5 w/iSight for letting me know I should mention this), USB2 booting is not supported, therefore you should remember OS X has no support for booting USB 2 and the firmware has no support. If this fails, there is a remote possibility that you can still boot off of USB2, but you may need to substitute ud for or something similar. The command would be similar to this: nvram boot-device ud:3,\\\\:tbxiNow this looks a tad bit different then what we typed in Open Firmware, but that's because we have to escape the two backslashes, each with a backslash of its own. Something like: boot-device ud:3,\\:tbxi hd:,\\:tbxi"Īnd now some more fun, there is a Unix script that can be written to enable this, because after all we are only changing a nvram variable.

Type printenv boot-device, and you should see the change displayed already.

Type setenv boot-device ud:3,\\:tbxi where the number after the colon corresponds to that partition number we found in step two.

Now type printenv boot-device, which will usually get you output of boot-device hd:,\\:tbxi.

Again, if you see this, I have not had this fail yet. If found, it will usually have beside it or something similar. In this list, look for ud, usually below where you see hd ( ud is "USB Disk," I presume). In Open Firmware, type devalias, and you should get a list as output. If this step does not work, I have had very limited success getting a machine to boot off USB2. Hold Command-Option-F-F right after the machine is turned on.

Start up the machine in Open Firmware (this is the fun part).

There are other ways of finding this out, but in my case, my disk is disk2s3 (the 3 on the end will come into play soon).

#MAC OS X INSTALL DISC FOR PWERBOOK G4 DRIVERS#

disk3s9 might be a USB disk with OS 9 drivers that is considered the third disk. That is, disk2s3 is usually for a USB disk with no OS 9 drivers installed that is the second disk disk. I usually find this by going to Disk Utility and looking at the info for the partition on the USB disk with OS X.

Connect the drive to your machine, and find out which partition the OS X system is installed on.

As you know, there are many different ways of getting a system on a USB drive contact me if you have any questions on how to do that, or search for that information.

You need a USB2 drive with an OS X system installed (I am using 10.4.3, though any I think will work as far as what the machine can boot).Note: As with all hints that have to do with Open Firmware, proceed at your own risk! I have not experienced a problem and I don't see how this hint could render your Mac useless, since the default can always be recovered by resetting the SMU. Without further delay, here's the process to follow.

iMac G5 w/iSight (thanks to the eager user who emailed me).

Machines that I have tested this hint on and made it work are: Thankfully, somewhere about the time the iMac G5 with the ambient light sensor (ALS) was released, Apple tweaked their Open Firmware, which allowed us to boot PowerPC Macs from USB2 drives. First off, I have tried and tried again over the years to boot various PowerPC Macs via a USB2 disk.